Roof using Shingle

Roof using Shingle
Roofing contractor repairing damaged roof on home after recent wind storms, many roofs were damaged

Roof using Shingle . Shingle is a low-cost roofing material that is not widely used in France. A shingle roof is designed to look like a slate roof. However, it should be noted that this roofing is much less durable than slate. Are you looking for concrete information about shingle roofing? Are you wondering how much a shingle roof costs, or when to install a shingle roof? This page provides detailed information about shingle roofing, its qualities and defects.

Shingle roofing originated in the United States, specifically North America, a little over a century ago. It is an inexpensive roofing material designed to mimic slate.

The composition of shingle roofing

Shingle is a strong roof covering. Composed of a layer of fiberglass sandwiched between two bitumens to ensure its resistance to UV (ultraviolet), it is a reliable, strong and waterproof material.

Today, shingle comes in all colors for more aesthetics: black, gray, green, yellow, red and other. Its most common version is the black version, which can look like slate roofing.

The installation of a shingle roof

Unlike most roofing materials, shingle roofing is easy to install and does not require extensive work. To limit your expenses and save even more on your budget, you can even install a shingle roof yourself (as long as you take the precautions associated with working at height, of course).

Here are two common techniques used to install shingles:

French style: this is a fastening technique performed on a batten, with the help of a hook (as for slate installation). This is the best way to successfully install a shingle roof. Note that this type of work can only be done if you have a good hand. If not, it is best to leave it to a professional roofer.
American style: this method is easier to do, but is rather reserved for annexed dwellings such as the roof of the garage, the garden or the greenhouse, the barn and others. Again, this practice is recommended for the experienced do-it-yourselfer. It consists of nailing the shingle directly to the wood frame already covered upstream.

In either case, shingle roofing is not recommended for a primary residence.

Note: Some brands even offer shingle that can be glued on, for an even easier (but less durable) installation.
Installing a shingle roof

American-style shingle installation is within the reach of any good handyman.

Characteristics of the shingle roof

The shingle roof is very flexible and easily adapts to different types of roofs, regardless of the slope. Its main advantage is its low price, combined with a beautiful aesthetic. Easy to install and very attractive from a budget point of view, the shingle roof is not perfect for all that! Let’s take a closer look at the characteristics of this roof covering.

The advantages of this roofing

Shingle is the ideal roof covering if you are on a budget, and you are looking for a roof for a secondary building.

Indeed, this roof benefits from many qualities:

Easy to install,
Very affordable (it is one of the least expensive roofs)
Resistant to fire and cold,
Aesthetic and timeless with different color choices,
Flexible and easy to handle.

If you are looking to install a roof covering yourself, it is obvious that the installation of such tiling is its main asset. Quite aesthetically pleasing, it is a suitable choice for a garden shed or workshop roof.

The disadvantages of shingle roofing

However, don’t be fooled by its very affordable price.

In fact, shingle roofing will suffer from a number of limitations, which are worth knowing about:

Poorly installed, this roof will be fragile, and the shingle could easily come off. Without additional insulation: shingles suffer from catastrophic thermal and sound insulation. That’s why we don’t recommend it on a main house.
The durability of a shingle roof is very low (about 20 years at most), and it is a roof that deteriorates quite quickly.

In the end, the shingle roof is only suitable for a garden shed or an uninhabited room. Its poor insulation and low durability will make you regret such a choice on a main house!
Shingle roofing

Shingle roofing is only suitable for an unheated building (garden shed, carport, etc.).

The price of a shingle roof

As mentioned above, the price of a shingle roof is clearly attractive. And for good reason, the price of such thatching can range from 8 to 15 € per m² on average (excluding installation costs), which is very advantageous.

The table below tells you more about the price of shingle roofing:
Shingle model Estimated price/m² (without installation)
Red iron-on shingle 8 to 10 € per sqm
Black shingle 8 to 12 € per m²
Green shingle 10 to 15 € per m²

Please note that the price of shingle installation by a professional is between 10 and 20 €/m² (excluding supplies). It is therefore also a very economical roofing material to install.

Couvreur Nantes Loire Atlantique

Tips For Hiring A Reputable Roofing Contractor

Tips For Hiring A Reputable Roofing Contractor
Roofers at work

Tips For Hiring A Reputable Roofing Contractor Curling or cracked shingles. Leaks in the ceiling. Too many asphalt granules in the gutters. Any one of these telltale signs can mean it’s time to replace your home’s roof. So where do you start? With a reputable contractor. Schedule time to sit down with three or more recommended roofers and ask the following questions:

  • What is the full name and address of the company? This will verify that the company is credible.
  • Does the company carry insurance? Contractors should carry both comprehensive liability insurance and workers’ compensation to protect you as the homeowner in the event that an accident occurs.
  • Is the company a licensed or credentialed contractor? Although not all states require licensing, it is a good indicator that the contractor is knowledgeable and dedicated.
  • How long has the company been in business? The longer the company has been in business, the better; the lifespan for most small businesses is three years.
  • Will the company provide referrals or references from previous jobs? Ask for a list of names and phone numbers of previous employers and try to get photos of the roofer’s completed work.
  • What is the company’s workmanship warranty? Warranties that cover the installer’s work should typically cover a minimum of a one-year time span.
  • What is the company’s track record for solving customer complaints? Request a referral from a job that involved a complaint. This will show the homeowner how the contractor handles problems when they do arise.
  • Get A Quote In Writing Each of your prospective contractors should provide you with a quote in writing, and do it promptly. If you have to wait for longer than a week for your quote, then that contractor isn’t prepared to handle your business efficiently. Those who hand you a detailed, well written quote promptly are those that are ready to handle your business.

Couvreur de Vannes Morbihan  Tips For Hiring A Reputable Roofing Contractor

What Is Landscape Architecture?

What Is Landscape Architecture?
Brick paved patio with comfortable patio furniture with modern armchairs and a stool around a table set with tea and cookies alongside a low curving wall overlooking a green lawn, high angle view

What Is Landscape Architecture? Many times I have been asked what is the difference between a landscape architect and a landscape designer. Hopefully the following will answer this question.

The American Society of Landscape Architects, ASLA, provides the following:

“Landscape architecture encompasses the analysis, planning, design, management, and stewardship of the natural and built environments. Landscape architectural projects include design of public parks, site planning for commercial and residential properties, land reclamation, urban and community design, and historic preservation. Examples of landscape architecture include Central Park in New York City, TRW’s headquarters outside Cleveland, the “Emerald Necklace” of green spaces and parks in Boston, Sursum Cordan Affordable Housing in Washington, D.C., preservation of Yosemite Park and Niagara Falls, and the landfill reclamation of Fresh Kills in New York. Landscape architects have advanced education, professional training, specialized skills, and are licensed in 47 states.”

What is the difference between a Landscape Designer and a Landscape Architect?

The national professional association is the American Society of Landscape Architects, based in Washington. ASLA full members have graduated from an accredited landscape architecture program, have 7 years of education and/or professional experience and are state licensed. In Michigan, as well as all other States, a three (3) day LARE examination administered by the Council of Landscape Architectural Registration Boards is required to be passed for state licensure.

Landscape designers do not have these professional credentials. Many state and local governments require designs to be stamped with a state registered Landscape Architect’s seal.

What Is Landscape Architecture : What can I expect the landscape architectural design process to be?

Various architects may have different approaches, yet all are aimed at the same result. Make sure you’re comfortable with the steps that the Landscape Architect defines. A typical process includes:

· Pre-planning – As the client, you discuss your desires with the architect and provide background, priorities, and any basic design guidelines. You’ll work together and define the overall scope and timeline. The result will be a proposed budget and statement of work. The landscape architect will then prepare a contract for you to sign.

· Project Planning – Further preliminary details are developed with you about the site and its function and usage. The site is analyzed and the Landscape Architect creates a list of development priorities, which you’ll approve.

· Preliminary Design – A review of the site, usage requirements, and environmental conditions are undertaken to create preliminary drawings. The Landscape Architect will show you design and presentation drawings showing the overall site concept. Initial construction cost estimates are provided, which you review and approve.

· Final design – Further detail is added to the concept. Material is selected and initial construction documentation is created. Where necessary, cost estimates are revised.

· Documentation – Additional detailed specifications and drawings are developed and provided to you for approval. The Landscape Architect may give you construction documents to assist you in soliciting bids from contractors and may help you review bids.

· Installation – Depending on your contract, the Landscape Architect may play an active role in representing you in your interaction with the contractor and provide on-site supervision. At the close of the project, the Landscape Architect will make a final inspection.

How do I find a good landscape contractor?

If you’re going to need referrals to contractors and other service providers as part of your project, ask the Landscape Architect about these people. They will typically have an array of competent people in the industry for you to contact.

What’s included in the landscape architecture contract?

Any reputable Landscape Architect will provide a written contract before beginning a project. This agreement will specify in detail the exact work to be done, the work schedule, the amount and payment terms of the landscape architect’s fees, and the responsibilities of each party to the contract.

As a registered landscape architect in the State of Michigan and principle architect with Sexton Ennett Design, LC, a landscape architectural firm in southeast Michigan, I am particularly aware of the professional responsibilities related to landscape design. If there are any questions please feel free to contact the ASLA or me.

Keywords:
landscape architecture, ASLA, equestrian, detroit suburbs, Michigan, oldenburg horses, architecte paysagiste Nantes

Get the Most Value from Your Roof Insulation

Value from Your Roof InsulationGet the Most Value from Your Roof Insulation. From fibreglass to foam, there are a variety of popular roof insulation materials. However, not all are created equal and some are more effective than others.

The basic gauge of the effectiveness of any insulation is its R-value. Insulation is designed to stop the flow of heat, says Roofer Lexington KY . The more heat the insulation stops, the higher the R-value of that insulation.

When compared to fibreglass batt insulation, spray foam insulation has a higher R-value at a given thickness. In other words, 2 inches of spray foam will insulate your roof better than 2 inches of fibreglass batts.

Cellulose fill, either blown-in or applied by hand, also has a higher R-value than fibreglass batts at the same thickness. But, again, the R-value of spray foam insulation is almost twice as high as cellulose fill insulation of the same thickness.

As important as R-value is in how well insulation works, it is not the only thing to consider when choosing the best roof insulation. Moisture will cause both fibreglass batts and cellulose fill to lose R-value. Even slight moisture, that you can’t see or feel, can reduce the R-value of fibreglass batts.

Neither fibreglass batts or cellulose fill insulation can seal every gap in your roof. Heat can pass through the open gaps and this reduces the R-value of the insulation, although the R-values listed for fibreglass or cellulose do not take this into consideration. In other words, the actual R-value of installed fibreglass batt or cellulose fill roof insulation is lower than the listed R-value.

Spray foam insulation is not affected by moisture, says Imprimantes 3D d’occasion. In fact, it can stop minor leaks because, when it is applied, spray foam insulation spreads to fill every gap and seal your roof. Pollutants and other airborne irritants that might get through the gaps left by batts and fill are kept out by spray foam insulation.

Perhaps best of all, insulating your roof with spray foam insulation costs about the same as other insulations.

The spray foam roof insulation specialists at Foam Comfort have the experience you need to get the most from your insulation.

Don’t Let Your Roof Repairs Go Sky High

Don't Let Your Roof Repairs Go Sky High

Don’t Let Your Roof Repairs Go Sky High  !  Before you go to the expense of calling in a roofing contractor, see if you can analyze and repair your roof problem yourself. The best possible time to repair your roof problem – is as soon as you realize that you have one and if the weather is calm enough to climb up onto the roof. In fact, this could be further qualified by saying that the best and most economical way to a trouble-free roof, is to inspect the roof regularly, so that you see the problem developing.

Before you go to the expense of calling in a roofing contractor, like Santa Rosa Roofing , see if you can analyze and repair your roof problem yourself. The best possible time to repair your roof problem – is as soon as you realize that you have one and if the weather is calm enough to climb up onto the roof. In fact, this could be further qualified by saying that the best and most economical way to a trouble-free roof, is to inspect the roof regularly, so that you see the problem developing.

A leak from one dislodged tile is a small and inexpensive matter, but if you do not inspect your roof regularly, this will go unnoticed. By the time that you DO notice it, it may be because water is dripping into your spare room! This means that this whole area of the roof structure is soaked, the ceiling will need to be replaced and hopefully the flooring will recover.

Always check your roof after a wind storm, says as most roofing is not designed to withstand fierce winds. Scrutinize the tiles for cracks, splits and torn-off corners; also check for lifting. Lifting is a common cause of roof leaks, and can be easily rectified. Be aware of multiple tiles lifting, as this could be a sign that the roofing material is too old and is warping from all the weathering.

Climb into your attic/loft and ensure that any insulation that you have in your roof is not right up against the roof itself. There has to be a gap for air to circulate; also when a roof heats up and there is insulation directly behind it, this heat is thrown back into the roofing and excessive heating like this can damage and warp the roof.

Another weakness in all roofs is the flashing, says Logiciels de Conception Assistée par Ordinateur . Flashing is designed to provide a watertight junction between roof materials and structure, especially if the roof projects out or changes design (as with extension roofs). If you are installing a new roof, it is worthwhile to get the flashing ‘inspected’ as it is a common failure area.

Often the simple fact that the gutters, leading into down pipes from the roof, are blocked with leaves and twigs can cause a problem. Roofs must have adequate run off, especially in the areas which may have snow. Water trapped in the gutter will mean that it will back up the roof for a few inches and have time to seep into the edges of the roofing tiles. Not all homes have adequate perimeter protection on their roofs, although this is one good feature to ask for on a new roof.

Quite often homes incur roof leaks all at the same time (often after strong gales winds and torrential rain etc). This can mean that all contractors are busy and you have ‘stop up the leak’ until you can get help.

If you do get a leak, and you have placed buckets under the dripping water, be aware that the leak may be in a completely different place than it would seem. Locating the source is difficult, as water can run along horizontal timbers and appear to be leaking from a place that is sound. Getting up into the attic and actually looking for a wet spot on the roof decking will be an accurate way to tell.

If you can find the spot an emergency patch can be made applying roofing felt and using plastic cement to hold it until you can call in a contractor. You can also attempt to repair it yourself, if it is just a shingle that is damaged. You can carefully prize up the roof shingle by removing the three or four nails that are holding it in place; next, apply a generous coating of tar beneath the tear in question, and also coat the underside of the shingle with a with a coat of tar before putting it back in place. Add a spot of tar to each nail head. Most roofing companies advise against the ‘liquid’ asphalt repair products.

Roofs can also be temporarily repaired using roof membrane and sealants. Care must be taken to clean the roof surface first to ensure that the sealant will stick and keep the leak protected from rain etc. In fact, as long as the roof is clean and dry, the wonder of the 20th. Century – duct tape – can also be stuck onto the roof!

Don’t Let Your Roof Repairs Go Sky High Don’t Let Your Roof Repairs Go Sky High

Decorate Your Concrete : Ideas for the Do-It-Yourselfer

Decorate Your Concrete : IdeasDecorate Your Concrete: Ideas for the Do-It-Yourselfer. Decorate your home’s concrete surfaces and give your patio, porch, garage, driveway, etc. a customized and refreshing new look. Acid stains, water based stains and epoxy paints are available for do-it-yourself projects.

You can enhance your home’s existing concrete surfaces using acid stains, water based stains , epoxy paints , and scoring techniques. If you’re tired of looking at dull gray concrete, says Driveway Seattle, there are some fairly easy projects for the serious do-it-yourselfer to give your concrete a refreshing new look. Or perhaps you plan to have some new concrete installed but you don’t want plain gray concrete. Decorative concrete work costs double to triple that of regular concrete and many people simply can’t afford it. There are inexpensive ways to decorate concrete after it has cured without having to pay skilled tradesmen.

Acid based concrete stains are becoming more and more popular for coloring concrete surfaces. They chemically react with the cementitious material to produce permanent color with variegated or mottled appearance like that of marble. This results in a natural, elegant looking surface. Acid stains are available in 8-10 different colors, mainly brown, green, and reddish earth tones. The cost is normally $60-$70 per gallon which covers 300-400 square feet. A coat of clear concrete sealer when you’re finished really brings out the colors and beauty of acid stains.

Water based concrete stains are an alternative to acid stains and are much more user friendly because they’re much less toxic. These stains don’t chemically react with the concrete; they are absorbed into the surface pores and act like a dye. The big advantage of water based stains is the wide array of colors available. You can find just about any color in the spectrum and create a more vibrant and consistent appearance. They also normally cost about $60-$70 per gallon which covers 300-400 square feet.

If you want to venture beyond the basic staining of concrete, consider using some scoring techniques to create patterns on the surface. You can make your concrete look like a tile floor for example, says Code postal Lyon . It’s up to your imagination. An angle grinder with a 4 inch grinding or cutting wheel is the ideal tool for this. The important thing to remember when scoring is to draw the pattern on the concrete first and make sure you’re satisfied with the way it looks because scoring is irreversible. Most people don’t own an angle grinder but you can rent one at almost any tool rental shop.

Epoxy paints make an excellent coating for garage floors and basement floors. Many commercial floors have epoxy coatings because of their durability and resistance to chemical spills as well as their appearance. In recent years, however, it has become very popular for residential use with an increasing availability of different colors. This is not a difficult project, but the key to successful application is surface preparation. Epoxy paints have also become available in a water based form making it safe for the do-it-yourselfer and ideal for indoor applications. They cost a little more than stains. For a 400 square foot garage, you’ll spend about $200 for the materials needed for this project.

Decorate Your Concrete : Ideas

Creative Concrete Stamping

Creative Concrete StampingCreative Concrete Stamping.  Stamping concrete is a great way for you to imitate the look and fee of authentic stone, brick, or pavement without having to spend as much. There are rubber patterns that create the impression of natural stone for this purpose. There are also ready-made patterns for such materials such as brick and cobblestone, however sometimes they can look artificial. One way to avoid this is to create your own patterns to be used in stamping concrete. If you can learn this you will soon find your inventory stock filled with varied patters that can be used for your various concrete stamping projects.

1. Be Innovative

You may even use design ideas you find around your home, says Concrete Jacksonville FL . For example, you could use an Indonesian batik design block. As long as it can make an impression on wet cement, and does not stick to the finished product, it will do. In good design, there are no limits to the imagination. So look around your area, you might even find an appealing pattern somewhere in your own home! You could consider looking at your garage, your attic, or even your uncle’s vacation gifts for potential stamp impressions.

2. Stamping

Commercial stamping produces great imitations, says Code Postal Lille . Sometimes, however, stampers are just overkill. You can bring out the beauty of concrete by being discreet at times with your stamping. You could use stamps that litter around your home, a batik woodblock or even a part of an auto transmission. Anything can be used to stamp the concrete as long it doesn’t stick and ruin the finished surface. It also has to be durable. A commercial stamp is perfect for improving a plain slab on concrete. You could also use this type of stamp if you desire a professional, standard looking concrete stamping.

3. Creative Stamping

Creating your own stamp tool is can be innovative and fun. You could even use a salvaged part from an old ceiling to create decorative stamp! When stamping on concrete, make sure you understand the risks this procedure entails. Commercial concrete stamps are designed to work well, and are engineered to be as easy to use as possible. They often leave a clean impression. If you were to use your own stamps made of everyday stamp-worthy items, remember that there is a risk that the concrete could be ruined. Commercial stamps are designed to consistently pull free from the concrete; this may not be the case with home-made ones.

– Even slabs with a deep-cut pattern must be jointed so that cracking can be controlled
– Divide the stamped concrete by using sawed joints
– Order correctly slumped concrete
– Lay out stamps before the concrete arrives
– Do as little hand tooling as possible
– Order proper amounts of concrete

Concrete stamping is neither for the inexperienced nor the faint of heart. For those who would like to learn this do-it-yourself art, learning concrete stamping is possible. For the hobbyists, masons, and even for those who just wish to make their homes better, this will truly be a worthwhile undertaking.

Creative Concrete Stamping

Do It Yourself Landscape Design – Where To Begin

Do It Yourself Landscape DesignDo It Yourself Landscape Design – Where To Begin. Here’s one answer to an all too common home landscaping question. How do I start my design? Where do I begin?

There’s an old saying that states something like – “Getting Started Is Half Finished”. And so many times I find this to be true as I see do it yourself landscapers struggle to find their initial design idea. However, once they establish a framework of necessary design elements, it usually goes pretty smooth from there.

It’s not surprising that the most common landscape design question that I get is – “where do I begin?” or “how do I start my design?”. I know it can be difficult. And especially if you don’t have a vision for your design.

So where do you begin? How do you start your landscape or garden design?

While every design is different and every designer follows a set of rules and principles, I find that most do it yourselfers all have the greatest success from using the same starting point. Begin by laying down any paths, driveways, access routes, or walk areas that might be needed. And also create access to any areas that you may plan on creating. In many designs, this will help to establish a framework that you can simply design around.

Of course, this won’t be applicable in all designs as many don’t require any access or travel. So take and use this advice where and if you can.

Paths and walkways can accomplish many functions in your landscape or garden , explains Philadelphia landscaper . Their main function, of course, is to create a designated space for people to walk on.

However, in design and as an aid to design,says Codes postal Marseille  their function could be to guide your visitors to, through, or away from some other area in the garden. Also, they’re a great way to break up a vast expanse of lawn, meadow, or bed area.

First, let’s look at walkways, paths, and such as necessary elements.

Walkways are needed to guide visitors or yourself to and from another area. Observe that almost every home has a walkway leading to the front door, which is, of course, where most folks want to invite guests to come. So walks, whether refined (brick, flagstone, etc.) or primitive (gravel, mulch, etc.), are necessary to “guide” or “lead” visitors to, through, or away from an area.

So where are the necessary areas where you need other walkways or access? Maybe from the back door to the alley where you dump the trash. Or from the house to the pool area. Or from the pool area to the kids play area or the outdoor cooking area. You get the picture.

In a design sense.

Establishing walk, drive, and access areas will in turn help to create borders and boundaries. Once you have your walkways laid out, you can simply design a lot of the landscaping around them. The same goes with driveways and parking areas as well. You can plant beds on either or both sides of a walk or use a walkway as an edge to create borders.

Keep it interesting if you can.

If you were to, for instance, plan to place a sitting area at the back of the garden. Of course you would need some type of path for you and your guests to get there. However, instead of plotting a straight path, why not create a winding tour through other interesting areas of the garden on the way there?

Curves and winding paths do more than just create interest. They can also create an illusion of more space, distance, and travel. This is especially useful in creating small gardens and landscapes.

Once you lay down walkways, driveways, and access areas, you’ll have a good starting framework for the rest of the design. Now, simply design around them.

How Vacuum Cleaners Work

How Vacuum Cleaners WorkHow Vacuum Cleaners Work. The are many different types of vacuum cleaners and carpet cleaning machines but they all work by using the same principal or idea. A vacuum is created in a tube or system and air is drawn into the system through a filter which catches debris and then the air is diffused from the unit out of an exhaust.

The residential upright vacuum cleaner uses the suction principal combined with a spinning brush at the suction opening which is located on the bottom of the vacuum cleaner. As the brush, which is commonly known as a beater bar, spins at a high rate of speed this beats the carpet and pushes and debris toward the suction opening. Once the debris has reached the suction opening air forces the debris into a filter bag which catches the debris but lets the air pass through. Once the air moves passed the filter bag it is expelled through an exhaust vent usually located on the handle box unit of the vacuum cleaner. Residential vacuums are given this name because they usually have one motor that runs the whole vacuum cleaner. This motor spins the brush and also operates the suction fan, explains Carpet cleaners Charlotte NC . Due to increased stress on one motor these types of vacuum cleaners do not have the longevity of a commercial vacuum but are priced relatively low.

Commercial vacuum cleaners work on the same principal as residential vacuum cleaners but are built for abuse and constant operation. Commercial vacuum cleaner parts are usually readily available and can be replaced by a vacuum cleaner technician, says Vin du Languedoc . Most commercial vacuum cleaners utilize two motors, one running the beater brush and the other running the suction fan or fans. These types of vacuums also utilize that latest technologies by using circuit boards to distribute the power to the vacuums two motors only when needed. On some newer commercial vacuum cleaners when the suction wand is used the beater brush motor will turn off or divert extra power for suction utilizing the entire motor potential of the vacuum cleaner.

Wet dry vacuums work on the same vacuum suction principal but extra safeguards must be put in place so that water does not come in contact with any electrical components or the motor. Wet dry vacuum cleaner motors are usually positioned on top of a debris canister and air is drawn in through the hose and up through the motor to an exhaust vent positioned on top. If water starts to reach the motor at the top of the canister a floating ball will close of the opening into the motor saving the motor from water damage. All on and off switches and electrical components on wet dry vacuums are sealed to prevent water penetration.

Cyclonic vacuum cleaners use high powered motors to create a vortex in the vacuum which creates suction. A beater bar pushes debris into the suction tube which is then drawn up into a sealed canister. Once in the canister the debris is moved toward the outer walls using centrifugal forces. The debris then slows down and is dropped into the bottom of the canister by utilizing gravity. Most cyclonic vacuums don’t use filter bags but sometimes this can compromise air quality because of escaping dust particles.

These days different types of vacuum cleaners are made for a specific purpose. It is recommended that you purchase a vacuum that fits it’s duties. If you plan to use your vacuum cleaner multiple hours everyday of the week it is not advisable to buy a residential vacuum cleaner. You will save money up front but most residential vacuums will probably not hold up over time and you will have to replace it faster. If wet floors are an issue then your best bet is a wet dry vacuum, most upright dry vacuums can stand some water but it will effect the performance of your vacuum cleaner over time.

Cleaning Your Own Carpeting

Cleaning Your Own CarpetingCleaning Your Own Carpeting. Cleaning your own carpet can be a great way to save money. If not done properly however you can end up with quite a mess. This article will give you some tips on using a carpet cleaning rental on your home’s carpets.
The first thing you need to do is find a good carpet cleaning machine. You can find them at most home improvement and grocery stores. Look for one in good condition that isn’t too beat up or old. The older the machine, the weaker the vacuum and water pump probably is. Find a machine in good condition and also purchase the carpet cleaning shampoo that is sold with the machines. Do not even think about using dish soap or any other homemade concoction.
The first step, once you get the machine home is to thoroughly pre-vacuum your carpet. Do not overlook this step because soil is much easier to remove when it is dry, tells  Carpet cleaner Buffalo NY  . Go over the carpet in several different directions, taking your time.
The next step is where I will differ from the directions on the carpet cleaning machine. They usually want you to fill the machine with a shampoo solution. This means that you are rinsing with the solution and you will leave a lot of residue. Instead, mix the cleaning solution in a separate pump-up sprayer. You can find one gallon garden sprayers at any home improvement store. Now spray the carpet evenly with the cleaner. Do not over wet the carpet, spray the solution evenly and then let it dwell for 5 to 10 minutes. Dwell time will allow the solution to break down and absorb the soils.
Next, fill the carpet cleaning machine with plain warm water, says modifier stl freecad . After letting the solution dwell, you will make a pass over the carpeting to rinse the cleaning solution out. If your carpet is heavily soiled or you used a lot of cleaning solution, you may need to make two passes over the carpet. Your goal here is to remove as much of the cleaner as possible in order to leave the least amount of residue.
Finally it is time to dry your carpets. The quicker you get them dry, the less likely it is that spots will return and the less likely you are to get water marks. Turn your ceiling fans on and get out any portable fans you have and aim them at the carpet. If it is a nice dry day, open your windows or doors. The more airflow you get to your room the better.
Well, that’s it. That’s all there is to it. Just remember to take your time and do not take shortcuts. Follow these simple steps and you can easily clean your own carpet.